MCU 32-bit Stellaris ARM Cortex M3 RISC 128KB Flash 2.5V/3V/3.3V 64-Pin LQFP Tray, LM3S5752-IQR50-A0, Texas Instruments

The Stellaris® LM3S5752 microcontroller is based on the ARM® Cortex-M3 controller core operating at up to 50 MHz, with 128 kB flash, 64 kB SRAM, a 32-ch DMA, and ROM preloaded with the StellarisWare Driver Library and BootLoader.The LM3S5752 also features real-time industrial connectivity, with a CAN controller, USB 2.0 Full Speed OTG/Host/Device, an SSI / SPI controller, an I2C interface, and a UART.The microcontroller also features intelligent analog capability, including 1 analog comparators and 6 channels of highly accurate 10-bit analog-to-digital conversion – with the ability to sample at speeds of 500K samples per second.Finally, the LM3S5752 microcontroller provides a 24-bit systick timer, 3 32-bit or 6 16-bit general-purpose timers, a watchdog timer, a battery-backed hibernation module with RTC and 256 bytes of non-volatile state-saving memory, a low drop-out voltage regulator so that only one supply voltage is required, brown-out reset, power-on reset controller, and up to 33 GPIOs.

  • 32-bit ARM® Cortex™-M3 50-MHz processor core with System Timer (SysTick), integrated Nested Vectored Interrupt Controller (NVIC), Memory Protection Unit (MPU), and Thumb-2 instruction set

  • Full-featured debug solution with debug access via JTAG and Serial Wire interfaces, and IEEE 1149.1-1990 compliant Test Access Port (TAP) controller

  • 128 KB single-cycle flash and 64 KB single-cycle SRAM

  • Internal ROM loaded with StellarisWare® software

  • Lower-power battery-backed Hibernation module with Real-Time Clock

  • ARM PrimeCell® 32-channel configurable µDMA controller

  • 0-33 GPIOs (depending on configuration) with programmable control for GPIO interrupts and pad configuration

  • ARM FiRM-compliant Watchdog Timer ; plus three General-Purpose Timer Modules (GPTM), each of which provides two 16-bit timers/counters and can be configured to operate independently

  • 10-bit Analog-to-Digital Converter (ADC) with six analog input channels and a sample rate of 500 thousand samples/second

  • Fully programmable 16C550-type UART with IrDA support

  • Synchronous Serial Interface (SSI), supporting operation for Freescale SPI, MICROWIRE, or Texas Instruments synchronous serial interfaces

  • Inter-Integrated Circuit (I2C) Interface, providing Standard (100 Kbps) and Fast (400 Kbps) transmission and support for sending and receiving data as either a master or a slave

  • Controller Area Network (CAN) Interface using CAN protocol version 2.0 part A/B and with bit rates up to 1 Mbps

  • Universal Serial Bus (USB) Controller with USB 2.0 full-speed (12 Mbps) and low-speed (1.5 Mbps) operation, 8 endpoints, and USB On-The-Go (OTG) mode

  • One integrated analog comparator configurable for output to initiate an ADC sample sequence, drive an output pin or generate an interrupt

  • Industrial-range 64-pin RoHS-compliant LQFP package

  • Характеристики

    Program_memory_type

    Flash

    Supplier_package

    LQFP

    Specifications

    http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=LM3S5752&&fileType=pdf

    Screening_level

    Industrial

    Schedule_b

    8542310000

    Ram_size

    64 KB

    Program_memory_size

    128 KB

    Product_dimensions

    10.2 x 10.2 x 1.45 mm

    Pin_count

    64

    Operating_temperature

    -40 to 85 °C

    Operating_supply_voltage

    2.5, 3, 3.3 V

    Watchdog

    1

    Analog_comparators

    1

    Eccn

    EAR99

    Instruction_set_architecture

    RISC

    Htsn

    8542310001

    Тип интерфейса

    CAN/I2C/SPI/SSI/UART

    Device_core

    ARM Cortex M3

    Data_bus_width

    32 Bit

    Country_of_origin

    United States

    Бренд

    On_chip_adc

    6-chx10-bit

    Min_operating_supply_voltage

    2.25, 2.3, 3 V

    Number_of_timers

    5

    Number_of_programmable_i_os

    33

    Msl_level

    3

    Mounting

    Surface Mount

    Max_speed

    50 MHz

    Max_processing_temp

    260 °C

    Max_operating_supply_voltage

    2.75, 3.6 V

    Lead_finish

    Matte Tin

    Артикул: LM3S5752-IQR50-A0

    Описание

    The Stellaris® LM3S5752 microcontroller is based on the ARM® Cortex-M3 controller core operating at up to 50 MHz, with 128 kB flash, 64 kB SRAM, a 32-ch DMA, and ROM preloaded with the StellarisWare Driver Library and BootLoader.The LM3S5752 also features real-time industrial connectivity, with a CAN controller, USB 2.0 Full Speed OTG/Host/Device, an SSI / SPI controller, an I2C interface, and a UART.The microcontroller also features intelligent analog capability, including 1 analog comparators and 6 channels of highly accurate 10-bit analog-to-digital conversion – with the ability to sample at speeds of 500K samples per second.Finally, the LM3S5752 microcontroller provides a 24-bit systick timer, 3 32-bit or 6 16-bit general-purpose timers, a watchdog timer, a battery-backed hibernation module with RTC and 256 bytes of non-volatile state-saving memory, a low drop-out voltage regulator so that only one supply voltage is required, brown-out reset, power-on reset controller, and up to 33 GPIOs.

  • 32-bit ARM® Cortex™-M3 50-MHz processor core with System Timer (SysTick), integrated Nested Vectored Interrupt Controller (NVIC), Memory Protection Unit (MPU), and Thumb-2 instruction set

  • Full-featured debug solution with debug access via JTAG and Serial Wire interfaces, and IEEE 1149.1-1990 compliant Test Access Port (TAP) controller

  • 128 KB single-cycle flash and 64 KB single-cycle SRAM

  • Internal ROM loaded with StellarisWare® software

  • Lower-power battery-backed Hibernation module with Real-Time Clock

  • ARM PrimeCell® 32-channel configurable µDMA controller

  • 0-33 GPIOs (depending on configuration) with programmable control for GPIO interrupts and pad configuration

  • ARM FiRM-compliant Watchdog Timer ; plus three General-Purpose Timer Modules (GPTM), each of which provides two 16-bit timers/counters and can be configured to operate independently

  • 10-bit Analog-to-Digital Converter (ADC) with six analog input channels and a sample rate of 500 thousand samples/second

  • Fully programmable 16C550-type UART with IrDA support

  • Synchronous Serial Interface (SSI), supporting operation for Freescale SPI, MICROWIRE, or Texas Instruments synchronous serial interfaces

  • Inter-Integrated Circuit (I2C) Interface, providing Standard (100 Kbps) and Fast (400 Kbps) transmission and support for sending and receiving data as either a master or a slave

  • Controller Area Network (CAN) Interface using CAN protocol version 2.0 part A/B and with bit rates up to 1 Mbps

  • Universal Serial Bus (USB) Controller with USB 2.0 full-speed (12 Mbps) and low-speed (1.5 Mbps) operation, 8 endpoints, and USB On-The-Go (OTG) mode

  • One integrated analog comparator configurable for output to initiate an ADC sample sequence, drive an output pin or generate an interrupt

  • Industrial-range 64-pin RoHS-compliant LQFP package

  • Детали

    Program_memory_type

    Flash

    Supplier_package

    LQFP

    Specifications

    http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=LM3S5752&&fileType=pdf

    Screening_level

    Industrial

    Schedule_b

    8542310000

    Ram_size

    64 KB

    Program_memory_size

    128 KB

    Product_dimensions

    10.2 x 10.2 x 1.45 mm

    Pin_count

    64

    Operating_temperature

    -40 to 85 °C

    Operating_supply_voltage

    2.5, 3, 3.3 V

    Watchdog

    1

    Analog_comparators

    1

    Eccn

    EAR99

    Instruction_set_architecture

    RISC

    Htsn

    8542310001

    Тип интерфейса

    CAN/I2C/SPI/SSI/UART

    Device_core

    ARM Cortex M3

    Data_bus_width

    32 Bit

    Country_of_origin

    United States

    Бренд

    On_chip_adc

    6-chx10-bit

    Min_operating_supply_voltage

    2.25, 2.3, 3 V

    Number_of_timers

    5

    Number_of_programmable_i_os

    33

    Msl_level

    3

    Mounting

    Surface Mount

    Max_speed

    50 MHz

    Max_processing_temp

    260 °C

    Max_operating_supply_voltage

    2.75, 3.6 V

    Lead_finish

    Matte Tin