ADC Single SAR 100ksps 12-bit Parallel 28-Pin PDIP N, MAX197BCNI+, Maxim Integrated

The MAX197 multi-range, 12-bit data-acquisition system (DAS) requires only a single +5V supply for operation, yet accepts signals at its analog inputs that may span both above the power-supply rail and below ground. This system provides 8 analog input channels that are independently software programmable for a variety of ranges: ±10V, ±5V, 0V to +10V, or 0V to +5V. This increases effective dynamic range to 14 bits, and provides the user flexibility to interface 4mA-to-20mA, ±12V, and ±15V powered sensors to a single +5V system. In addition, the converter is overvoltage tolerant to ±16.5V; a fault condition on any channel does not affect the conversion result of the selected channel. Other features include a 5MHz bandwidth track/hold, a 100ksps throughput rate, software-selectable internal or external clock and acquisition, 8+4 parallel interface, and an internal 4.096V or an external reference. A hardware active-low SHDN pin and two programmable power-down modes (STBYPD, FULLPD) are provided for low-current shutdown between conversions. In STBYPD mode, the reference buffer remains active, eliminating start-up delays. The MAX197 employs a standard microprocessor (µP) interface. A three-state data I/O port is configured to operate with 8-bit data buses, and data-access and bus-release timing specifications are compatible with most popular µPs. All logic inputs and outputs are TTL/CMOS compatible. The MAX197 is available in 28-pin DIP, wide SO, SSOP, and ceramic SB packages. For a different combination of ranges (±4V, ±2V, 0V to 4V, 0V to 2V), refer to the MAX199 data sheet. For 12-bit bus interface, refer to the MAX196 and MAX198 data sheets.

  • 12-Bit Resolution, 1/2LSB Linearity
  • Single +5V Operation
  • Software-Selectable Input Ranges:±10V, ±5V, 0V to 10V, 0V to 5V
  • Fault-Protected Input Multiplexer (±16.5V)
  • 8 Analog Input Channels
  • 6µs Conversion Time, 100ksps Sampling Rate
  • Internal or External Acquisition Control
  • Internal 4.096V or External Reference
  • Two Power-Down Modes
  • Internal or External Clock

Характеристики

Volt_supply_source

Single

Number_of_analog_inputs

8

Sampling_rate

100 ksps

Volt_reference

External, Internal

Digital_supply_support

No

Architecture

SAR

Resolution

12 Bit

Typical_power_dissipation

30 mW

Differential_nonlinearity

1 LSB

Input_type

Voltage

Input_signal_type

Single-Ended

Input_volt

±10 V, ±5, 10, 5

Бренд

Msl_level

1

Country_of_origin

United States

Eccn

EAR99

Htsn

8542390001

Lead_finish

Matte Tin

Mounting

Through Hole

Operating_temp

0 to 70 °C

Pin_count

28

Product_dimensions

35.05 x 7.87 x 4.45 mm

Schedule_b

8542390000

Specifications

https://4donline.ihs.com/images/VipMasterIC/IC/MAXM/MAXMS07912/MAXMS07912-1.pdf?hkey=52A5661711E402568146F3353EA87419

Number_of_adc_channels

8

Polarity_of_input_volt

Bipolar, Unipolar

Operating_supply_volt

4.75, 5 V, 5.25

Number_of_adcs

1

Digital_interface_type

Parallel

Артикул: MAX197BCNI+

Описание

The MAX197 multi-range, 12-bit data-acquisition system (DAS) requires only a single +5V supply for operation, yet accepts signals at its analog inputs that may span both above the power-supply rail and below ground. This system provides 8 analog input channels that are independently software programmable for a variety of ranges: ±10V, ±5V, 0V to +10V, or 0V to +5V. This increases effective dynamic range to 14 bits, and provides the user flexibility to interface 4mA-to-20mA, ±12V, and ±15V powered sensors to a single +5V system. In addition, the converter is overvoltage tolerant to ±16.5V; a fault condition on any channel does not affect the conversion result of the selected channel. Other features include a 5MHz bandwidth track/hold, a 100ksps throughput rate, software-selectable internal or external clock and acquisition, 8+4 parallel interface, and an internal 4.096V or an external reference. A hardware active-low SHDN pin and two programmable power-down modes (STBYPD, FULLPD) are provided for low-current shutdown between conversions. In STBYPD mode, the reference buffer remains active, eliminating start-up delays. The MAX197 employs a standard microprocessor (µP) interface. A three-state data I/O port is configured to operate with 8-bit data buses, and data-access and bus-release timing specifications are compatible with most popular µPs. All logic inputs and outputs are TTL/CMOS compatible. The MAX197 is available in 28-pin DIP, wide SO, SSOP, and ceramic SB packages. For a different combination of ranges (±4V, ±2V, 0V to 4V, 0V to 2V), refer to the MAX199 data sheet. For 12-bit bus interface, refer to the MAX196 and MAX198 data sheets.

  • 12-Bit Resolution, 1/2LSB Linearity
  • Single +5V Operation
  • Software-Selectable Input Ranges:±10V, ±5V, 0V to 10V, 0V to 5V
  • Fault-Protected Input Multiplexer (±16.5V)
  • 8 Analog Input Channels
  • 6µs Conversion Time, 100ksps Sampling Rate
  • Internal or External Acquisition Control
  • Internal 4.096V or External Reference
  • Two Power-Down Modes
  • Internal or External Clock

Детали

Volt_supply_source

Single

Number_of_analog_inputs

8

Sampling_rate

100 ksps

Volt_reference

External, Internal

Digital_supply_support

No

Architecture

SAR

Resolution

12 Bit

Typical_power_dissipation

30 mW

Differential_nonlinearity

1 LSB

Input_type

Voltage

Input_signal_type

Single-Ended

Input_volt

±10 V, ±5, 10, 5

Бренд

Msl_level

1

Country_of_origin

United States

Eccn

EAR99

Htsn

8542390001

Lead_finish

Matte Tin

Mounting

Through Hole

Operating_temp

0 to 70 °C

Pin_count

28

Product_dimensions

35.05 x 7.87 x 4.45 mm

Schedule_b

8542390000

Specifications

https://4donline.ihs.com/images/VipMasterIC/IC/MAXM/MAXMS07912/MAXMS07912-1.pdf?hkey=52A5661711E402568146F3353EA87419

Number_of_adc_channels

8

Polarity_of_input_volt

Bipolar, Unipolar

Operating_supply_volt

4.75, 5 V, 5.25

Number_of_adcs

1

Digital_interface_type

Parallel